Tips / un********ed functions

At the top of the main-menu and every folder, the keys 1 to 9 are shortcuts to the icons 1-9

- A shortcut on the left menukey in standby-mode will take more time to open than a shortcut on the right menukey. Reason: The left key is also used for the keylock so it shortly waits for pressing the * button.

- While writing **** press and hold "#" to switch between Alpha mode and Number mode. You can also press a key long to insert its number.

- In standby-mode, press and hold 0 to launch your wap home page.

- If you have your keylock activated just press the on/off button to turn on your backlight to look at the time when it's dark without having to unlock the keypad.

- To keep the backlight on, run Torch (freeware), press and hold the Menu button and go somewhere else on the phone.

- To check your current firmware version simply type *#0000# in standby screen.

- To check your IMEI (International Mobile Equipment Identity) type *#06# in standby screen.

- To check your Bluetooth device address type *#2820# in standby screen.

- Start up in Safe Mode (no 'auto start' apps will be running): Hold down the pencil key when you turn on the phone and hold it on until you have to enter your PIN code.

- Format the phone memory by typing *#7370# in standby screen.

- In standby mode,
45# + <talk> dials the number on your sim in memory slot 45.
50# + <talk> dials slot 50 and so on.

MMC Card


Your files in MMC are stored in multiple (disk) blocks.
So if you format using 16K block, the space used will be 16K eventhough your file is just 1K.

If you buy MMC, it is usually preformatted with 16K block. Therefore alot of space is wasted as most installed program files are usually less than 2K.

You will need a card reader to do this:-

1. Connect card reader and copy all your files in the MMC to computer disk.
(Make sure you set the show all/hidden/os files to "on")
2. Do a format of the MMC using command line "format" and use the /A=size option.
Alternative, you can use the Disk Management in Adminstrative Tools to format.
Make sure you select FAT. For 256MB MMC, smallest block you can use is 4K, 128MB is 2K, 64Mb is 1K and 32MB is 512B.

(Note: You cannot use the phone "format MMC" to do this as the format just clear the al******** table and does not change the block size)

3. Copy back all files to MMC.

Now you will find that you will have more space.
256mb MMC got back 30+ mbs

Call number transmission * 31 # - { CLIR - Calling LINE identification Restriction switches on for the general call number transmission }
# 31 # - switch off the general call number transmission
# 31 # [ telephone number ] - with the next call suppress the own call number (thus temporary)
* 31 # [ telephone number ] - with the next call transfer own call number (thus temporary)
* # 31 # - status query (of call number transmission)
# 31 * [ telephone number ] - own call number show, although receiving station switched call number suppression on. (is not usually de-energised of the Netz(betreiber).)

* 30 # - switch { TIE-clip - Calling LINE identification presentation for the announcement on of the call number of the caller }
# 30 # - switch off
* # 30 # - status query

This also partly goes with 6600 via Men: Attitudes - calls - own No. send...

The following codes are not supported by most Netz(betreibern):
* # 76 # - announcement of the call number, under which one reached the calling (not its call number during rufumleitung!) { COLP - COonnected LINE identification presentation }
* 76 # - switch on
# 76 # - switch off

* # 77 # - announcement of the call number, under which the caller reached me (not my call number during rufumleitung meinerseits!) { COLR - COnnected LINE identification Restriction }
* 77 # - switch on
# 76 # - switch off

Call bypasses (call Forwarding) Bypass code (U): U=21 always
U=61 retards
U=62 not attainable
U=67 occupies

U=61, 62, 67 can be parallel active

U=21 - > and then no more call signaling overwrites U=61,62 and 67!
Service code (D):
Not all nets support all services
D=10 ******** and fax (all calls)
D=11 only ********
D=12 all data (speed/minutes)
D=13 only fax
D=14 DATEX j (active?)
D=15 teletex (active?)
D=16 only SMS
D=18 all data except SMS
D=19 all services except SMS
D=20 all services
D=21 all asynchronous services
D=22 all synchronous services
D=23 3.1 kHz GSM of ******** services
D=24 all synchronous POINT ton of POINT DATA inclusive. PADs
D=25 only data (all asynchronous POINT ton of POINT DATA inclusive. PADs)
D=26 DATA pack exchange on the left of inclusive. PADs
D=27 services thru PADs
D=29 12 Kbps digitally left